ASTM D3389 PDF

This standard is issued under the fixed designation D ; the number 1 This test method is under the jurisdiction of ASTM Committee D on Rubber. ASTM D is an abrasion method used for coated materials and is cited for classification testing by the ANSI standard. ASTM D Abrasion resistance tests are intended to measure the wear resistance properties of a material. This may be correlated to expected end use.

Author: Grom Vokinos
Country: Yemen
Language: English (Spanish)
Genre: Software
Published (Last): 20 November 2012
Pages: 446
PDF File Size: 10.3 Mb
ePub File Size: 14.62 Mb
ISBN: 888-9-17769-169-1
Downloads: 54286
Price: Free* [*Free Regsitration Required]
Uploader: JoJojind

To determine the abrasion resistance of textile fabrics using the rotary-platform double-head tester. The test methods included are listed in Table 1. This European Standard specifies requirements for surfaces for indoor facilities for multi-sports use. This guide covers the determination of the abrasion resistance of textile fabrics using the rotary platform, double head tester RPDH. Number of cycles determines abrasion rating.

This Japanese Industrial Standard specifies the testing methods for the evaluation of general characteristics of woven fabric foundation cloth. This SAE Recommended practice applies to the abrasion resistance testing of decorative tapes, graphics, and pin striping.

Mechanical property of film — Section 9: Where more than one test method is listed for the same characteristic, no attempt is made to indicate superiority of one method over another. EN Annex E Laminate floor coverings – Elements with a surface layer based on amnioplastic thermosetting resins – Specifications, requirements and test methods This annex specifies the method for measuring abrasion resistance and consequently determining the abrasion class of laminate floor covering elements.

This test measures the ability of the surface of high-pressure decorative laminate to resist abrasive wear-through of the decorative layer. This Regulation applies to safety glazing and glazing materials intended for installation as windscreens or other panes, d389 as partitioning, on power-driven vehicles and their trailers.

The below links summarize popular Taber test methods and are sorted astn application e. Resilient floor coverings – Determination of wear resistance – Part 2: These practices cover the selection and use of procedures for testing polymeric powders and powder coatings.

This specification covers metallic stemmed femoral prosthesis used to replace the natural hip joint sstm means of hemi-arthroplasty or total hip surgical procedures. Vitreous and Porcelain Enamels- Characteristics of the enamel coatings applied to steel panels intended for architecture.

The number of revolutions of the specimen required to cause a defined degrees of abrasion is used as measures of resistance to abrasion.

ASTM C Standard Specification for Prefaced Concrete and Calcium Silicate Masonry Units This specification covers prefaced concrete masonry units with the exposed-to-view-in-place surfaces covered at the point of manufacture with resin, resin and inert filler, or cement and inert filler to produce a smooth resinous tile facing.

  DESIGNING INTERACTIVE SYSTEMS BENYON PDF

LAT Hard Anodizing Dd3389 method covers the requirements for anodization of aluminum and it alloys MIL-AF 1 Military Specification – Anodic Coatings for Aluminum and Aluminum Alloys This specification covers the requirements for six types and two classes of electrolytically formed anodic coatings on aluminum and aluminum alloys for non-architectural applications.

Screed, bases and in situ floorings.

This method is intended for determining the abrasion resistance of d389 in terms of percent v3389 in breaking strength, or breaking strength after a given period of abrasion, or the number of abrasion cycles required to produce a specified state of destruction. This specification does not address, and therefore is not applicable to, ground-face concrete masonry units that are manufactured by grinding a thin layer off the surface of a concrete masonry unit to expose aggregates within and polishing to produce smooth, architectural finish.

This specification covers requirements for the compound and physical characteristics of rubber floor tile. ASTM E Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings This specification covers minimum asstm performance and laboratory test procedures for non-reinforced liquid coating encapsulation products single or multiple-coat systems for leaded paint in buildings.

It is intended as a means of characterizing coatings used on surgical implants.

BS EN Surfaces for sports areas – Determination of resistance to abrasion of non-filled synthetic turf This document describes a method for the determination of the wear resistance of a non-filled synthetic turf surface using an abrasive wheel under laboratory conditions.

See tests 12 and This process standard specifies procedures and requirements for hard anodizing aluminum alloys.

Studies have shown that Wyzenbeek test results on the same fabric can and do vary significantly from test to test. The test described measures the ability of the surface layer to resist abrasive wear-through. Tappi T Abrasion Loss of Paper and Paperboard Taber-type method The objective of this method is to determine the resistance of surfaces of paper and paperboard to the action of abrasion, either wet or dry, by measuring abrasion loss.

This standard sets out a method for the determination of the abrasion resistance of textile fabrics applicable to all textile fabrics including coated and laminated fabrics, a method for wet testing is also specified.

A fabric with twice the number of abrasion cycles does not indicate double the service life. This specification covers the requirements for photosensitive anodized aluminum sheets and foils.

ISO Road Vehicles – Safety Glazing Materials – Mechanical Tests This International Standard specifies mechanical test methods relating to the safety requirements for all safety glazing materials in a road vehicle, whatever the type of glass or other material of which they are composed.

  BROKEN APRIL ISMAIL KADARE PDF

Therefore, ACT does not recommend using absolute numbers for comparision. Two test methods are included.

This is an oscillating test. This part of ISO specifies a method for determining the resistance to abrasion of a dried film of paint, varnish or related product, using abrasive rubber wheels and abrading by making a rotary movement. This document sets forth recommended minimum performance standards for vinyl and other polymeric films, plain and printed, which are used as in-ground swimming pool liners.

DIN and Taber 5155 Abrasion

Specifications, test methods, and usage provisions for safety materials used for glazing of motor vehicles and motor vehicle equipment operating on land highways. Not applicable to indoor tennis halls. This guide covers the selection and use of test methods for high-performance interior architectural wall coatings HIPAC which differ form more conventional coatings in that they are tougher, more stain-resistance, more abrasion-resistant and, ordinarily, designed to be applied to wall surfaces of steel, masonry, and plaster or gypsum wallboard.

This test can be used to determine the resistance to scuffing of test specimens such as fiberboards, fabrics, vinyl coated fabrics, leathers, and similar trim materials. This SAE recommended practice covers the requirements for rubber floor mats made from five types of rubber compound as required by the physical property requirements of the application.

Wyzenbeek results abovedouble rubs have not been shown to be an indicator of increased lifespan.

Taber Abrasion ASTM D D D

ASTM F Annex A1 Standard Specification d389 Implantable Saline Filled Breast Prosthesis This specification covers the requirements for single use saline inflatable, smooth and textured silicone shell implantable breast prostheses, intended for use in surgical reconstruction, augmentation, d33389 replacement of the breast. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

EN Wood-based panels-Melamine faced boards for interior uses-Test Methods This test measures the ability of the decorative surface of melamine surfaces boards to resist abrasive wear-through by rotating a specimen in contact with cylindrical wheels covered with abrasive paper.

A Wyzenbeek machine is used for this test allowing samples of the test fabric to be pulled tight in a asym and held stationary.