ASTM D543 PDF

ASTM D CHEMICAL RESISTANCE. These practices cover the evaluation of all plastic materials including cast, hot-molded, cold-molded, laminated. Buy ASTM D PRACTICES FOR EVALUATING THE RESISTANCE OF PLASTICS TO CHEMICAL REAGENTS from SAI Global. ASTM D , Standard Practices for Evaluating the Resistance of Plastics to ASTM D , Standard Test Method for Abrasion Resistance of Organic.

Author: Fenris Fenrizilkree
Country: Morocco
Language: English (Spanish)
Genre: Career
Published (Last): 5 December 2018
Pages: 371
PDF File Size: 4.84 Mb
ePub File Size: 2.96 Mb
ISBN: 356-4-74818-912-3
Downloads: 75510
Price: Free* [*Free Regsitration Required]
Uploader: Zolot

Base the selection of test conditions on the manner and duration of contact with reagents, the temperature of the system, d534 stress, and other performance factors involved in the particular application.

The most typical physical strength properties evaluated are tensile strength and elongation. Send us a request Wilton UK: Formally confirming that your products and services meet all trusted external and internal standards.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Variations in test coupon depth indicate that these test plates had greater variation in depth across the plate than the other test plates. Work Item s – proposed revisions of this standard.

Chemical Compatibility ASTM D543

This slight angle resulted in laminate coupons being moderately wider on one face top compared to bottom. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. All weight and dimension changes were less than 0. Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards. All test laminate coupons measured approximately mm in length by 25 mm in width and 5 mm in depth.

Provisions are made for various exposure times, stress conditions, and exposure to reagents at elevated temperatures. The type of conditioning immersion or wet patch depends upon the end-use of the material.

Further testing is d534 to verify that BOD greater than PPM significantly reduces the laminate flexural yield stress and flexural modulus. It should also be noted that two of the coupons 1 lb and c show much higher stress-strain response than a. The test includes provisions for reporting changes in weight, dimensions, appearance and strength properties. This test covers the evaluation of plastic materials for resistance to chemical reagents, simulating performance in potential end use environments.

  ESTIMATION AND COSTING BY BN DUTTA PDF

If used as a container or transfer line, immerse the specimens.

Chemical Compatibility ASTM D

Provisions are made for various exposure times, strain conditions and elevated temperatures. Certification Formally confirming that your products and services meet all trusted external and internal standards. If the material d5433 only see short exposures or will aztm used in close proximity and reagent may splash or spill on the material, the wet patch method of applying reagent should be used.

Atm applications involving continuous immersion, the data obtained in short-time tests are of interest only in eliminating the most unsuitable materials or indicating a probable relative order of resistance to chemical reagents.

Weight and Dimensions Changes, test results indicate that the laminate product had no significant visible appearance changes after exposure to the chemicals reagent and that weight and depth changes are greater than width and length changes. The test samples are then sealed in a container, and either left at room temperature or placed in an oven. Further testing is required to confirm the influence of BOD reduction on the coupon flexible yield stress.

While measuring the laminate coupons it was noted that the specimen edges were at a slight angle with respect to the depth of the material. The strain fixtures and laminate coupons were placed in Plastic containers filled with chemical reagent. These practices include provisions for reporting changes in weight, dimensions, appearance, and strength properties. Active view current version of standard.

Details to know more click here http: Sunday, March 15, astm d Through our network of over 43, people in 1, laboratories and offices in countries, Intertek provides quality and safety solutions to a wide range of industries around the world.

This standard and ISO Part 3 address the same subject matter, but differ in technical content and the results cannot be directly compared between the two test methods. Enabling you to identify and mitigate the intrinsic risk in your operations, supply chains and business processes. Assurance Testing Inspection Certification. Validating the specifications, value and safety of your raw materials, products and assets. This standard does not purport to address all of the safety concerns, if any, associated with its use.

  C# LOCALREPORT PDF

If the material will only see short exposures or will be used in proximity and reagent will splash or spill on the material, use the wet patch method of applying reagent.

This standard and ISO Part 3 address the same subject matter, but differ in technical content and the results cannot be directly compared between the two test methods. This slight angle is a characteristic of the JetCut process. The values given in brackets are for information only. The choice of types and concentrations of reagents, duration of immersion or stress, or both, level of stress, temperature of the test, and properties to be reported are necessarily arbitrary.

Testing Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards. It was found that two and half rotations produced the desired strain and that the strain level remained constant over a seven-day period. The values given in parentheses are for information only.

The influence of coupon thickness on the flexural yield stress is not known at this time. Inspection Validating the specifications, value and safety of your raw materials, products and assets.

The device uses a three point bending design with coupon contact dimensions similar to those used in the D test. Specific hazards statements are given in R543 7.

ASTM D – 14 Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents

Standard reagents are specified to establish results on a comparable basis. Provisions are made for various exposure times, stress conditions, and exposure to reagents at elevated temperatures.

Link to Active This link will always route to the current Active version of the standard. Historical Version s – view previous versions of standard.